Half Square Triangle – Fat Quarter Tutorial

In a previous post I promised a tutorial for making lots of half square triangles (HST’s) from fat quarters, so here goes. First, I would like to emphasize that accuracy is of the utmost importance, in marking, sewing and cutting. Also, this is still producing HST’s, so it is still time consuming, but it is organized, systematic and produces scads of HST’s from one process.

Press two fat quarters, a dark and a light:
IMG_5486

Align them right side together with the dark fat quarter on the bottom facing right side up and with the light fat quarter on the top facing right side down:
IMG_5485

Align one short edge of the stacked fat quarters with the bottom line on your cutting mat. Use a 24 inch cutting ruler and a fine marker to draw a line at a right angle to the bottom edge. This line serves the same purpose as a “clean up cut” would. Make sure that both fabrics are under this line:
IMG_5487

IMG_5488

Draw lines parallel to your first vertical line a distance of 2 3/8 inches apart for finished HST’s of 1 1/2 inches:
IMG_5489

Draw lines the same distance apart at right angles from the short edge of the fabrics:
IMG_5491

IMG_5492

All the vertical and horizontal lines have been drawn at this point:
IMG_5493

Draw lines from corner to corner of each drawn square in one direction only. All the diagonal lines will be parallel:
IMG_5494

Draw lines a 1/4 inch from each side of the diagonal line. These will be the diagonal sewing lines:
IMG_5495

All the vertical, horizontal and diagonal lines have been drawn at this point:
IMG_5496

Pin lots of places between the diagonal lines, making sure you will have room to machine sew on the diagonal lines:

IMG_5497

IMG_5499

Sew on the diagonal lines just a needle’s width (scan 1/4 inch) inside the diagonal sewing lines:
IMG_5500

As your sewing progresses to the corners, lots of fabric will be in the throat of the machine. Loosely roll it up to keep it out of the way:
IMG_5501

All the diagonal sewing lines have been sewn:
IMG_5502

IMG_5503

Using a 24 inch cutting ruler and rotary cutter, cut all the vertical lines:
IMG_5504

Stack three strips at a time, off-setting the strips by about 1/4 inch and matching the horizontal drawn lines:
IMG_5505

Using a cutting ruler and rotary cutter, cut all the horizontal lines:

IMG_5506

Cut all the diagonal lines between the sewn diagonal lines. The resulting stack of HST’s:
IMG_5507

Most of the HST’s will have a short sewn corner. Insert your finger or a stiletto between the two layers of fabric and tug and these stitches will release and come out:
IMG_5508

Using a small, sharp scissors trim the corners as shown:
IMG_5510

Press the seam of each HST toward the dark. Pressing from the right side makes it easy to avoid pleats at the seam line:
IMG_5511

Pretty, isn’t it?
IMG_5513

When I drew the lines on this sample I had a six by eight grid resulting in 48 squares and, eventually, 96 HST’s.

IMG_5514

You can make these any size you want. Draw the squares 7/8 inch larger that the desired size of the HST as it will appear in your pieced quilt (sometimes referred to as “finished” size). The following chart may be helpful:
HST-FQ Chart

Advertisements
This entry was posted in HST-FQ Tutorial, Tutorial and tagged , , , , . Bookmark the permalink.

One Response to Half Square Triangle – Fat Quarter Tutorial

  1. Pingback: QST Nightmare

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s